- How to setup ultimate traffic live fsx steam install#
- How to setup ultimate traffic live fsx steam trial#
- How to setup ultimate traffic live fsx steam simulator#
Either before the sim is started or after - both ways work and planes appear relatively quickly when utl_client is started. I will, until another solution comes along, have to manually start the process. Now, everything I had read in other forums indicated that utl_client was supposed to start when the sim started. Wait 8-10 minutes (as per recommended in some other forums) and the Ground Controller begins to chatter, planes begin to move on the ground, planes takeoff and planes land. Back to the sim.Īircraft on the ground everywhere. So I started the utl_client manually (it's in the UTL directory that contains the Imagery, SimConnect, Uninstall and utLive Aircraft folders).
No aircraft and no utl_client process running. Started the sim and then started Task Manager. More searching of forums until I found a post that talked about making sure that the utl_client process was running while the sim was running. Back to the sim, hoping that was the answer I was looking for. Some 480 were in need of updating so that was done (automatically by Steam). I went to Steam and validated all my FSX-SE files. Remembering that a version of SimConnect was apparently installed by UTL, I wondered if the version was incorrect for FSX-SE. I followed those directions, but my results didn't look like the video. I found a youtube video with instructions for reloading/restoring SimConnect. One forum post cited the possibility that the SimConnect version being used might not be correct for FSX-SE. I found references to possible SimConnect issues and the UTL utl_client.exe file as possible contributors to my situation. After all the above-mentioned steps and having not made any apparent progress, I began researching once again.
How to setup ultimate traffic live fsx steam install#
What have I done wrong? Is there, perhaps, an entry missing in the fsx_se.cfg? Was it an error to install UT Live on my G: drive where my FSX-SE lives rather than the default C: drive? I can't find any help anywhere at this point.Ĭan someone point me in the right direction, please? The only way to get traffic is to put the trafficaircraft.bgl back in to Scenery/World/Scenery. I have a flight world inhabited only by my own aircraft. Nothing at the gates, nothing on the ground anywhere, nothing in the air, nothing landing or taking off. Second problem - there are still no aircraft at any airport I visit Lambert Field in St.
I can see flights moving on the map and the status board changes as flights arrive and depart, but nothing happens in the sim.) Is that correct? If I start the ui, the flight map and the status are not active until I start the simulation as outlined above. (NOTE: I read in another post somewhere that UT Live starts automatically when you start FSX-SE. My airports are completely devoid of aircraft other than the one I am using in the sim. I have FSX-SE running with no default (or any other) AI. I know this because text appeared indicating the save process was successful and the simulation was initialize and running.
How to setup ultimate traffic live fsx steam trial#
Through a process of trial and error, I was able to determine the sequence of buttons accessed by the Tab key and then by pressing Enter could save settings and start the simulation. For some reason the hide/expand options do no respond to keyboard shortcut keys. I am only able to exit the application using ALT-F4. (Screen resolution is set to 1920 x 1080.) The UT Live window extends above and below the limits of my monitor's display area.
How to setup ultimate traffic live fsx steam simulator#
After the installation completed, I started UT Live and proceeded to configure it as per the InstallGuide - set the UI to run as an administrator, started UT Live and checked that Dovetail Games FSX Steam Edition is the current active flight simulator and attempted to start the simulation.įirst problem - the hide/expand/close options are not visible on the screen and neither are the Save Settings or Start Simulation buttons. The installation went smoothly without errors and I followed the InstallGuide to the letter. I am also posting this in the UT support forum. Perhaps someone will have some information that will help me. I know this is not the UT Live support forum, but there are a lot of knowledgeable users here.